SUBSCRIBE TO TMCnet
TMCnet - World's Largest Communications and Technology Community

TMCNet:  Notice of Receipt of Petition that Nonconforming 2012 McLaren MP4 Passenger Cars are Eligible for Importation Posted in Federal Register

[March 03, 2014]

Notice of Receipt of Petition that Nonconforming 2012 McLaren MP4 Passenger Cars are Eligible for Importation Posted in Federal Register

(Targeted News Service Via Acquire Media NewsEdge) by GEMA VIANA Targeted News Service WASHINGTON, March 3 -- The U.S. Department of Transportation published the following notice in the Federal Register from the National Highway Traffic Safety Administration: Notice of Receipt of Petition for Decision that Nonconforming 2012 McLaren MP4[12C] Passenger Cars are Eligible for Importation A Notice by the National Highway Traffic Safety Administration on 03/03/2014 Publication Date: Monday, March 03, 2014 Agencies: Department of Transportation National Highway Traffic Safety Administration Dates: The closing date for comments on the petition is April 2, 2014.


Comments Close: 04/02/2014 Entry Type: Notice Action: Receipt of petition.

Document Citation: 79 FR 11869 Page: 11869 -11871 (3 pages) Agency/Docket Numbers: Docket No. NHTSA-2014-0004 Notice 1 Document Number: 2014-04563 Shorter URL: https://federalregister.gov/a/2014-04563 ACTION Receipt Of Petition.

SUMMARY This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that nonconforming 2012 McLaren MP4[12C] passenger cars that were not originally manufactured to comply with all applicable Federal Motor Vehicle Safety Standards (FMVSS), are eligible for importation into the United States because they are substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards (the U.S.-certified version of the 2012 McLaren MP4[12C]) and they are capable of being readily altered to conform to the standards.

DATES: The closing date for comments on the petition is April 2, 2014.

ADDRESSES: Comments should refer to the docket and notice numbers above and be submitted by any of the following methods: Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the online instructions for submitting comments.

Mail: Docket Management Facility: U.S. Department of Transportation, 1200 New Jersey Avenue SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-0001 Hand Delivery or Courier: West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., between 9 a.m. and 5 p.m. ET, Monday through Friday, except Federal holidays.

Fax: 202-493-2251 Instructions: Comments must be written in the English language, and be no greater than 15 pages in length, although there is no limit to the length of necessary attachments to the comments. If comments are submitted in hard copy form, please ensure that two copies are provided. If you wish to receive confirmation that your comments were received, please enclose a stamped, self-addressed postcard with the comments. Note that all comments received will be posted without changeto http://www.regulations.gov, including any personal information provided. Please see the Privacy Act heading below.

Privacy Act: Anyone is able to search the electronic form of all comments received into any of our dockets by the name of the individual submitting the comment (or signing the comment, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78).

How to Read Comments submitted to the Docket: You may read the comments received by Docket Management at the address and times given above. You may also view the documents from the Internet at http://www.regulations.gov. Follow the online instructions for accessing the dockets. The docket ID number and title of this notice are shown at the heading of this document notice. Please note that even after the comment closing date, we will continue to file relevant information in the Docket as it becomes available. Further, some people may submit late comments. Accordingly, we recommend that you periodically search the Docket for new material.

FOR FURTHER INFORMATION CONTACT: George Stevens, Office of Vehicle Safety Compliance, NHTSA (202-366-5308).

SUPPLEMENTARY INFORMATION: Background Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not originally manufactured to conform to all applicable FMVSS shall be refused admission into the United States unless NHTSA has decided that the motor vehicle is substantially similar to a motor vehicle originally manufactured for importation into and sale in the United States, certified under 49 U.S.C. 30115, and of the same model year as the model of the motor vehicle to be compared, and is capable of being readily altered to conform to all applicable FMVSS.

Petitions for eligibility decisions may be submitted by either manufacturers or importers who have registered with NHTSA pursuant to 49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice in the Federal Register of each petition that it receives, and affords interested persons an opportunity to comment on the petition. At the close of the comment period, NHTSA decides, on the basis of the petition and any comments that it has received, whether the vehicle is eligible for importation. The agency then publishes this decision in the Federal Register.

J.K. Technologies, LLC. of Baltimore, Maryland (Registered Importer 90-006) has petitioned NHTSA to decide whether nonconforming 2012 McLaren MP4[12C] passenger cars are eligible for importation into the United States. The vehicles which J.K. Technologies believes are substantially similar are 2012 McLaren MP4[12C] passenger cars that were manufactured for sale in the United States and certified by their manufacturer as conforming to all applicable FMVSS.

The petitioner claims that it compared non-U.S. certified 2012 McLaren MP4[12C] passenger cars to their U.S.-certified counterparts, and found the vehicles to be substantially similar with respect to compliance with most FMVSS.

J.K. Technologies submitted information with its petition intended to demonstrate that non-U.S. certified 2012 McLaren MP4[12C] passenger cars, as originally manufactured, conform to many FMVSS in the same manner as their U.S. certified counterparts, or are capable of being readily altered to conform to those standards. Specifically, the petitioner claims that non-U.S. certified 2012 McLaren MP4[12C] passenger cars are identical to their U.S. certified counterparts with respect to compliance with Standard Nos. 102 Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect, 103 Windshield Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems, 106 Brake Hoses, 113 Hood Latch System, 116 Motor Vehicle Brake Fluids, 118 Power-Operated Window, Partition, and Roof Panel Systems, 124 Accelerator Control Systems, 126 Electronic Stability Control Systems, 135 Light Vehicle Brake Systems, 138 Tire Pressure Monitoring Systems, 202 Head Restraints, 204 Steering Control Rearward Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention Components, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat Belt Assembly Anchorages, 212 Windshield Mounting, 214 Side Impact Protection, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion, 225 Child Restraint Anchorage Systems, 301 Fuel System Integrity, and 302 Flammability of Interior Materials.

The petitioner also contends that the vehicles are capable of being readily altered to meet the following standards, in the manner indicated: Standard No. 101 Controls and Displays: replacement of the instrument cluster with a U.S.-model component and reprogramming the vehicle computer.

Standard No. 108 Lamps, Reflective Devices and Associated Equipment: replacement of the headlamps, front and rear side marker lamps, and tail lamps with U.S.-model components and reprogramming the vehicle computer to activate necessary systems.

Standard No. 110 Tire Selection and Rims for Motor Vehicles with a GVWR of 4,536 kilograms (10,000 pounds) or Less: installation of a tire and rim information placard.

Standard No. 111 Rearview Mirrors: replacement of the passenger side rearview mirror with a U.S.-model component or inscription of the required warning statement on the face of that mirror.

Standard No. 114 Theft Protection and Rollaway Prevention: reprogramming the vehicle computer to activate the key warning system.

Standard No. 201 Occupant Protection in Interior Impact: inspection of each vehicle for the presence of compliant "A" pillar airbags to verify compliance with the standard.

Standard No. 208 Occupant Crash Protection: The petitioner states that the vehicles meet the standard, and are equipped with all components needed to meet the standard's advanced airbag requirements. However, due to varying world market regulations each vehicle must be inspected for compliance with the standard. For example, the presence of knee bolster airbags and seat belt warning systems must be confirmed, and if not present, installed or modified to comply.

Standard No. 214 Side Impact Protection: inspection of each vehicle for the presence of compliant "A" pillar airbags and to verify compliance with the standard.

Standard No. 401 Interior Trunk Release: installation of U.S.-model interior trunk release components.

The petitioner states that the bumpers and bumper support structure are identical to that of the U.S. certified model. However, the bumper reinforcements and brackets must be inspected to ensure that the correct components were installed prior to importation. If not, they must be replaced with U.S.-model components to comply with 49 CFR part 581.

The petitioner additionally states that a vehicle identification plate must be affixed to the vehicles near the left windshield post to meet the requirements of 49 CFR part 565.

Because the subject petition covers nonconforming vehicles likely to have been manufactured on or after September 1, 2006, compliance with the advanced air bag requirements of FMVSS No. 208 is of significant concern to the agency. NHTSA is therefore particularly interested in comments regarding the ability of a Registered Importer to readily alter the subject vehicles to fully meet the driver and front outboard passenger frontal crash protection and child passenger protection requirements of FMVSS No. 208. The following is a partial listing of the components that may be affected: a. Driver's frontal air bag module b. Passenger frontal air bag module c. Passenger frontal air bag cover d. Knee air bags e. Knee bolsters f. Passenger outboard frontal seat belt system g. Driver and front outboard seat assemblies including seat tracks and internal seat components h. Steering wheel components, including the clock spring assembly, the steering column, and all connecting components i. Instrument panel j. Instrument panel support structure (i.e. cross beam) k. Occupant sensing and classification systems, including sensors and processors l. Restraint control modules m. Passenger air bag status indicator light system, including related display components and wiring n. Wiring harnesses between the restraint control module, occupant classification system and restraint system components o. Control system computer software and firmware All comments received before the close of business on the closing date indicated above will be considered, and will be available for examination in the docket at the above addresses both before and after that date. To the extent possible, comments filed after the closing date will also be considered. Notice of final action on the petition will be published in the Federal Register pursuant to the authority indicated below.

AUTHORITY: 49 U.S.C. 30141(a)(1)(A), (a)(1)(B), and (b)(1); 49 CFR 593.7; delegation of authority at 49 CFR 1.95 and 501.8.

Claude H. Harris, Director, Office of Vehicle Safety Compliance.

For more information about Targeted News Service products and services, please contact: Myron Struck, editor, Targeted News Service LLC, Springfield, Va., 703/304-1897; editor@targetednews.com; http://targetednews.com.

TNS 30VianaGem-140303-1153049 (c) 2014 Targeted News Service

[ Back To Technology News's Homepage ]

OTHER NEWS PROVIDERS







Technology Marketing Corporation

800 Connecticut Ave, 1st Floor East, Norwalk, CT 06854 USA
Ph: 800-243-6002, 203-852-6800
Fx: 203-866-3326

General comments: tmc@tmcnet.com.
Comments about this site: webmaster@tmcnet.com.

STAY CURRENT YOUR WAY

© 2014 Technology Marketing Corporation. All rights reserved.