Freescale Intelligent Battery Sensor Combines MCU and CAN with Flexible Three-Channel Analog Front End [Global Data Point]
(Global Data Point Via Acquire Media NewsEdge) Designed to support both conventional and emerging battery chemistries for automotive and industrial applications, the MM9Z1J638 battery sensor measures key battery parameters for monitoring state of health (SOH), state of charge (SOC) and state of function (SOF) for early failure prediction. A flexible four-cell front end architecture supports conventional 12V lead acid batteries as well as emerging battery applications, such as 14V stacked cell Li-Ion, high voltage junction boxes, and 24V truck batteries.
Battery failure is one of the leading causes of vehicle breakdowns due to electrical system errors. Rising levels of electrical load in vehicles are placing increased strain on batteries as new, mission-critical requirements such as engine start-stop functionality become increasingly common. According to analyst firm Strategy Analytics, more than 52 million vehicles worldwide will support start-stop functionality by 2020. Start-stop requirements, together with others such as regenerative braking and intelligent alternator control, are driving demand for more precise sensing of the battery's state to provide early failure warnings.
"Our introduction of the industry's first single-package, automotive-qualified intelligent battery sensor with MCU and CAN components will help automakers cope with increasing algorithm complexity and data communication demands as cars become more connected and intelligent," said James Bates, senior vice president and general manager for Freescale's Analog %7E Sensors Group. "Also featuring integrated functional safety support, the new MM9Z1J638 battery sensor helps to support vehicle reliability even as automotive electrical system complexities increase."
Integrating a 16/32 bit S12Z microcontroller with 128K Flash, 8K RAM and 4K EEPROM together with a CAN protocol module, LIN interface and a three-channel analog measurement front end, the MM9Z1J638 battery sensor combines analog, processor and communication functions in a single package to help lower total bill of materials and accommodate advanced battery monitoring algorithms. The analog front end includes a two-channel, 16-bit sigma delta (S?) analog-to-digital converter (ADC) for simultaneous measurement of battery voltage and current, as well as a third 16-bit S? ADC for temperature monitoring using the integrated sensor and redundant measurement plausibility checks to support functional safety. The new Freescale product's input battery voltage measurement capability supports a wide range up to 52V directly to the device as well as much higher voltage battery configurations when used with external voltage dividers. Its low operating duty cycle enables operation in low-power mode for a majority of the time to help lower average system power consumption. The MM9Z1J638 is fully AEC-Q100 automotive qualified and designed to meet stringent automotive standards for ESD, EMC and zero defect quality levels.
Reference designs with integrated hardware and software support for the MM9Z1J638 battery sensor enable quick and easy development of new applications, including energy storage systems, uninterruptible power supplies, hospital equipment and alarm systems. Low-level drivers and BMS utility libraries are available to support custom battery modeling and shorten development cycles. The KIT9Z1J638EVM evaluation board is priced at $188.80(USD) and demonstrates key features of the MM9Z1_638. Reference design RD9Z1-638-4Li is priced at $220.80(USD) and demonstrates product capabilities for 4-cell Li-Ion battery applications.
Additional Product Details
•16/32 bit MCU, 128K Flash, 8K RAM, 4K EEPROM
• Integrated CAN protocol module
• 3x 16-bit ADC for current, voltage and temperature
• Support for up to four cells and up to 52V inputs
• Multiple low-power modes
• Multiple wake-up triggers (current, temperature, etc.)
• Configurable hardware filters
• Robust LIN physical layer
• 7 x 7 mm 48-pin QFN package
Availability and Pricing
The MM9Z1J638 battery sensor is available now from Freescale and authorized distributors worldwide for a suggested resale price of $3.61(USD) in 10,000-unit quantities. Please contact Freescale Sales for additional quantities.
Robust and reliable analog performance
The majority of Freescale analog products meet critical industrial market requirements, including operation across extended temperature ranges. These products are designed and manufactured with rigorous process controls, and qualified using industry standard methodologies designed to yield defect rates in line with the stringent requirements of the automotive market. The MM9Z1J638 battery sensor is included in Freescale's product longevity program, which provides assurance of supply for a minimum of 10 or 15 years from the time of launch.
(c) 2014 GlobalData Provided by Syndigate.info, an Albawaba.com company
[ Back To Technology News's Homepage ]